CM Test Bench V2

Discussion in 'Modding Worklogs' started by Ace_finland, Dec 13, 2012.

  1. Ace_finland

    Ace_finland Member

    Joined:
    Dec 11, 2012
    Messages:
    8
    Hey guys,

    First post so hope this is in the right section :)

    Background:
    I entered the Cooler master mod competition this year and thought.
    I was thinking for ages for a case to pick and by accident I found the test bench by Cooler Master at a local computer store. I knew instantly that this is the case I wanted to modify. It's different enough to other cases and I didn't find anyone else in the competition using the same case.
    After countless hrs designing i think i came up with something worthwhile doing.
    The original case
    [​IMG]
    This was the design I stuck with for now unless i change my mind for a 100th time
    [​IMG]
    Also started fabricating the radiator boxes today.
    Started with some kinda straight pieces of 1mm sheet metal. Decided on 1mm thickness to add some stability and still easy to fabricate.
    [​IMG]
    The machine
    [​IMG]
    Bent a small test piece to figure out the radius and the measurement, also to get all the angles right.
    [​IMG]
    Made four pieces so i can mess up two, easier to make extra now than going back to make two new ones :)
    [​IMG]
    Quick test fit to see how its gonna look
    [​IMG]
    [​IMG]

    Also some parts arrived :)
    [​IMG]

    Back after a lot of hrs in the garage and at the workshop at work. Not much of an update when it's full of fail but thought i would share anyways.
    Plan A
    Cut a template of the size i wanted
    [​IMG]
    Mark the piece to be cut
    [​IMG]
    Working with my best friend :) (angle grinder)
    [​IMG]
    After a lot of filing.
    [​IMG]
    [​IMG]
    After this i realized cutting the next 3 slots in the metal will make it very thin and will flex and bend a lot. And the plan is to powder coat it after i'm done with it, so i can't use any filler. so over to...
    Plan B
    Decided to get all the cuts before bending. Don't mind the tolerances, just forgot to adjust the digits
    [​IMG]
    Make a "table" for the mill at work.
    [​IMG]
    Used double sided sticky tape between the table and the metal sheets to prevent the pieces to vibrate during milling.
    [​IMG]
    Fastened the sheets with screws in as many places as possible, i did not want the sheet to move during milling.
    [​IMG]
    Let the milling begin. Still a Manual mill so need to be very focused :)
    [​IMG]
    More fasteners used as it progressed.
    [​IMG]
    Almost done, still need to clean all the edges and as you can see in the red circle i made a bit of a mess. I had just finished that slot and turned the mill off without turning off the feed. So when i turned the mill on it went like a bat out of.... :( Words cannot describe the feeling when that happened. I had spent 6 hrs milling just to do a simple mistake. Anyways, gonna weld it back and see if i can file it down. Wouldn't be a problem if i could use filler.
    [​IMG]
    welded and grinded down the mess i did the other day :)
    Got the sheets bent today but now i don't know if i should go with the circular mesh or the hexx mesh. The hexx mesh is made out of 1mm aluminum and the circular mesh is made out of steel sheet which would make the whole construction a lot more stable.
    [​IMG]
    [​IMG]
    [​IMG]

    Found another mesh today but not really liking it
    [​IMG]
    Also tried some powder coating last night
    This is satin black. Two problems with this color, fingerprints sticks instantly, and it looks kinda cheap
    [​IMG]
    Gun metal gray. Had to try, not gonna paint it like this though
    [​IMG]
    This is the surface finish of the original cooler master case. I'm really liking this surface finish so i'm gonna order some textured powder coating black and give it a try.
    [​IMG]
    Gonna order this color and give it a go!
    [​IMG]
    Got a lot done the last week so thought i would post a few pictures
    First of all I'll show you something great when working with metal sheets. I have not seen many use these and i don't know why. They are quite handy when you don't want to weld and will help a lot in hard to reach places, when you don't have to use a regular nut. It's rivet nuts :)
    Works like a normal rivet.
    [​IMG]
    Modified a normal rivet gun buy cutting the head of a M4 bolt and jamming it in the rivet gun. Added a few washers to prevent the rivet from entering the gun
    [​IMG]
    Screw the nut on the thread
    [​IMG]
    All done
    [​IMG]
    In the end I just got a rivet gun made for the rivet nuts which made it a lot easier.
    [​IMG]
    Made some acrylic for the case. Had to countersink the acrylic in order to get it flush against the case
    [​IMG]
    Mounted. It's clear acrylic but it has a green protective sheet on it.
    [​IMG]
    Spot welded some ends on the radiator holders and mounted it all together
    [​IMG]
    Removed the green protective plastic. Still needs to be sanded to get a matte finish so the red leds will spread the light better.
    [​IMG]

    Drilled the front acrylic plate. Still need to remove a lot of acrylic in the middle
    [​IMG]
    Drilled holes in the aluminum after i knew the acrylic would fit.
    [​IMG]
    Test fit
    [​IMG]
    During the test fit i marked around the edges with a knife so i could get a rough template.
    [​IMG]
    As you can see its a bit rough :) Will still do some more welding on the case and when that is all done i will grind down the front and back plate and sand it smooth. But you can see its starting to look as the rendering :)
    [​IMG]
    Sneak preview
    [​IMG]
    Almost forgot to update, have another project that I've been working on for the last 5 months. Can anyone guess what it is? Just got the "table back from a workshop that leveled it for me. So now i just need to get it assembled and it should be good to go if I just can figure out how to use it :D
    [​IMG]
    Back on topic
    Started sanding the edges, tried a lot of different machines and files before getting the result i wanted. Still need to straighten up the edges but wanted to mill the fan controllers first in case i make a mistake and need to redo it. [​IMG]
    [​IMG]

    Milled away a bit of material to get the psu as close as possible to the back of the case to make as much room as possible inside the case
    [​IMG]
    Started disassembling the new lamptron's
    [​IMG]
    Very easy to take apart
    [​IMG]
    In the preview yday you saw the milling so no need to post more pics of that, the controller fitted!
    [​IMG]
    Had to power it up :)
    [​IMG]
    [​IMG]

    After looking for leds for the acrylic and realizing buying "computer leds" are way too expensive i started looking for other options. Found this through a company in Finland. I don't know the price but it should be less than 50€ for 5m of leds. These are 15,6W/m so should be plenty of lumens :)
    [​IMG]
    The Leds can be cut every three leds and cables can be soldered on straight on the copper tabs, 8mm wide and 2,5mm high. The best thing with them is if you have a 2cm led strip or a 5m led strip all you need is 12V.
    [​IMG]
    [​IMG]

    Also have milled the front acrylic, milled a 3mm gap to place the leds in, a nice tight fit.
    [​IMG]
    From the top
    [​IMG]
    Full 12V, probably need to run them on 8V, otherwise with 2m's of leds it will look like a nuclear power plant :D
    [​IMG]
    As low as it goes.
    [​IMG]
    Still need to sand the acrylic edges to make it more smooth and spread the light even better, but it's a good start.
    Got some great news guys. After some discussions with EK Waterblocks they decided to sponsor me in this build!
    Since I started water cooling I have always liked the design of the water blocks that EK provide. So it is truly an honor to work with such a great company!
    [​IMG]
    The parts :)
    [​IMG]
    Unpacked
    [​IMG]
    This i won over at cooledpc.com but thought i would share it anyways
    [​IMG]
    Pump top to add some performance
    [​IMG]'
    EK-DDC X-TOP CSQ - Acetal, such a buty
    [​IMG]
    Waterblock for my Asus Gene-V, EK-MOSFET ASUS M5G
    [​IMG]
    EK-CoolStream RAD XT (240)
    [​IMG]
    A bunch of fittings, some i have bought and some sponsored
    [​IMG]
    EK-RES X3 150
    [​IMG]
    EK-FC5X0 GTX GW Backplate - Black
    [​IMG]
    Special thanks to Gregor over at EK for helping me out!
    Been quite busy the last few days having time off work in order to be able to finish the mod for the competition.
    Started with some motherboard raisers, was gonna machine them in aluminum but then i found this nice red Ø20mm plastic bar. Not the right red but they won't be seen after its installed and it's so easy to machine in plastic.
    First i machined them to the right diameter
    [​IMG]
    Drill and tap
    [​IMG]
    All done!
    [​IMG]
    Test fitted the pumps and the rads to check for clearance issues
    [​IMG]
    This looks a bit weird, but its in the middle of the case. Had to cut some space for the cables from the psu, this should be enough.
    [​IMG]
    All sanded and ready to get glass blasted
    [​IMG]
    Glass blasted and ready to be powdercoated
    [​IMG]
    It looks a bit uneven but its smudges from me fingering it, i didn't see it but it shows up in the photos, will clean it off before the final shots!
    [​IMG]
    Radiator box, or whatever you would call it
    [​IMG]
    Rear side of the same part
    [​IMG]
    Almost assembled
    [​IMG]

    And some final shots of the case itself, I really like the way it looks and glass blasting the acrylic made a really matte finish which hopefully will hide the single leds and give an even light throughout the acrylic.
    [​IMG]

    [​IMG]
    [​IMG]
    [​IMG]
    Still need to cut slots in some of the acrylic to be able to install all the leds.
    Also need to make something to hold the GPU's in place, i know what i want now so I just have to fabricate it.
    Finally decided to go with circular mesh, the hex mesh i got was only 1mm thick aluminum and was not stable enough. This is the color i went with, gun metal gray. Will make a slight contrast to the black powder coating.
    [​IMG]
    For quite a while I've been thinking about what to do for GPU supports, I've seen a few versions out there but nothing that would fit my mod. The biggest problem has been production time of something more complicated that i would have to mill or grind from aluminum. So when I finished another project of mine (homebuilt CNC router) I decided to put it into its first good use (haven't had time to use it since all my time has been spent on the case).
    This is what i wanted but wouldn't have had time to complete without the router. Test mount straight after milling all three parts.
    [​IMG]
    Glass blasted and painted. Also countersunk one side and threaded M5 threads into the rear of the aluminum.
    [​IMG]
    Close up of the support
    [​IMG]
    Now you are probably wondering how i will physically attach the gpu's to the support. Haven't had time to see if it works but there is no reason this shouldn't. You mount it from the rear of the support so the tab from the GPU go between the support and the "extra bit" Then you just turn the screws to pinch the tab from the GPU to the support.
    [​IMG]
    Also tried some engraving, my gf wasn't happy with the font, placement, size and basically everything, but I like it, It's about 0.5mm deep
    [​IMG]
    Also covers a extra hole in the case, although this won't be visible when the motherboard is installed but still a nice touch :) Still needs a bit of filing to make it fit perfect.
    [​IMG]
    Had to assemble the case in order to figure out where to drill holes in the mesh, so figured i would try to take a photo of the leds going at the same time, took around a 100photos before my gf snapped these two. It still doesn't show off the real red but it is awesome in my eyes :D This is as low as it goes, if i crank it up all the way u won't see the case. Gonna check with some ppl if there is a solution to get this right for the final shots.
    [​IMG]
    [​IMG]
    Getting close to the end of the Coolermaster competition! Have been very busy the last weekend, spent around 30hrs on the computer on saturday and sunday and had to take today off work just to get it up and running. Taking it to get photographed tomorrow so i can get some proper shots of it for the competition.
    Anyways, gonna start with the parts. A lot of the parts are from my previous build but there are also new parts
    Coolermaster test bench
    Intel 3570K
    Asus Maximus GENE-V
    Corsair Dominator Platinum 16GB 1600MHz
    128gb OCZ Vertez 2 SSD
    Corsair AX850 PSU
    2 X Gainward GTX570
    2 x Lamptron FC5 V2
    4 x Schyte Gentle Typhoon
    A lot of leds

    Watercooling:
    2 x EK-FC5X0 GTX GW Backplate - Black
    2 x EK-RES X3 150
    2 x EK-DDC X-TOP CSQ - Acetal
    2 x EK-CoolStream RAD XT (240)
    1 x EK-MOSFET ASUS M5G - Acetal + Nickel
    1 x EK Supremacy cpu block
    1 x EK Dual parallell sli block
    2 x laing ddc pumps
    A lot of EK fittings
    Mayhem's Aurora tharsis red
    [​IMG]
    Sleeved the led wires, the cat loves it
    [​IMG]
    Installed in the acrylic
    [​IMG]
    The lamptrons installed
    [​IMG]
    Mounted the rads and the fans to an xspc rad mount, quite a tight fit, a little bit over 1mm to spare :)
    [​IMG]
    Plumbing done on loop 1, was a bit more difficult than i first expected. Ignore the blue cables, resleeved them after
    [​IMG]
    Had to check what it looked like with the Hyper212 that i've used during the build. Had to remove all the water cooling so i could get all the sizes right
    [​IMG]
    So many cables, had to cut every cable and shorten them, they would not fit in the case as is.
    [​IMG]
    Tried to get hold of some genuine CoolerMaster sticker but it was a lot harder than i expected. So contacted Coolermaster and got approved to make my own stickers. Was gonna go with normal stickers but due to the case is slightly textured it wouldn't look good so went with these polyurethane based "3D" stickers. Got a few different color combinations made so i could pick the one i liked the most. Big thanks to Mr Glasberg over at staffans.fi for making these priority 1 and making them in more or less a day [​IMG]
    [​IMG]
    Assembled and more or less ready to go. Still have a lot to do but this will have to do for the competition.
    Leak test ongoing
    [​IMG]
    [​IMG]

    So here we go. As I'm looking through the pictures taken yesterday i realize i should have taken a lot more. Anyways, here are most of them without posting very similar looking ones. Enjoy!

    Without leds on. Sadly a few fingerprints on it but better with them there than photoshopped away :)
    [​IMG]
    [​IMG]

    Gpu loop
    [​IMG]

    [​IMG]

    [​IMG]

    Leds on
    [​IMG]
    [​IMG]
    [​IMG]

    Still have a few things to do with the computer but this will be it for the coolermaster mod competition. Wanna try to make my ram look like the gpu support with the same red glow. Not sure if its gonna work but gonna give it a go, also have some other ideas. But will have a week or two break now, need to sort out the rest of my life that has been left aside while building this.

    Did a compilation photo of the mod for the competition so thought i would post it here aswell.
    [​IMG]

    Sponsored by:
    [​IMG]
     
  2. pieceofchance

    pieceofchance Member

    Joined:
    Sep 28, 2011
    Messages:
    447
    Location:
    Country VIC
    very nice, and doing its rounds, I see...
     
  3. Jimba86

    Jimba86 Member

    Joined:
    Jul 13, 2011
    Messages:
    1,820
    Location:
    Brisbane 4179
    Nice mod!:thumbup:
     
  4. OP
    OP
    Ace_finland

    Ace_finland Member

    Joined:
    Dec 11, 2012
    Messages:
    8
    Thanks! Yeah, its on a lot of places, hope its not against the forum rules :)

    Thank you!
     
  5. jjjc_93

    jjjc_93 Member

    Joined:
    Jul 3, 2009
    Messages:
    2,095
    Location:
    Perth
    A full build in a single post, awesome. I always lose interest somewhere through updates even if it is a cool build.

    Nice work dude, looks nice!
     
  6. OP
    OP
    Ace_finland

    Ace_finland Member

    Joined:
    Dec 11, 2012
    Messages:
    8
    Ithanks! Its not done yet but thats how far i got for the cooler master mod competition :) go vote for me on their facebook page if u like it :)
     
  7. OP
    OP
    Ace_finland

    Ace_finland Member

    Joined:
    Dec 11, 2012
    Messages:
    8
    Thanks for all who voted for me in the Cooler Master mod competition! Got myself a 3rd prize :)

    After a very busy Christmas I've made a prototype of the ram, did not go well at all but at least i've gotten started.

    This is the design. It's basically the same design as the Dominator platinum ram but with a sandwich construction consisting of two aluminum sides with acrylic in the middle.
    [​IMG]

    The aluminum part
    [​IMG]

    One of the aluminum parts pressed together with the acrylic. Got decent tolerances on the parts so i just pressed them together with a vice, no glue needed :)
    [​IMG]

    Made a red light bar so the ram would match the case better. Still want a white acrylic top with it only being red when its on :)
    [​IMG]

    Installed without a lightbar
    [​IMG]

    It looks the same with a lightbar. Think there is not enough light for the light to reflect all the way to the middle of the ram. I will experiment a bit more but if i can't figure it out i will leave it with just a red lightbar

    With the red lightbar and the original part it looks like this. It's not too bad but a bit of the white light shines through due to the fact that the leds are further apart than the width of the lightbar. The red bar is the same width as the original one. Also gonna polish the entry surface of the acrylig to let as much light through as possible
    [​IMG]

    Sponsored by:
    [​IMG]
     
  8. OP
    OP
    Ace_finland

    Ace_finland Member

    Joined:
    Dec 11, 2012
    Messages:
    8
    Thanks to all that has been following me this year and a happy new year to you all! Next post will be next year :)
     
  9. OP
    OP
    Ace_finland

    Ace_finland Member

    Joined:
    Dec 11, 2012
    Messages:
    8
    Hey guys!
    Back now, been very busy with work and a lot of other stuff.

    Have been trying my best to get the ram working but after corsairs "release" on monday i decided to shelf my idea.

    I tried making grooves and so on in the acrylic and i got the light to spread decently as far as the new corsair kits are covered. Maybe they had the same problem :D Anyways, I will move on to some other mods i want to try out instead. Updates to come as soon as i make some progress :)

    Oh, also got the Rig Of The Year over at guru 3D!
     
  10. mad_mic3

    mad_mic3 Member

    Joined:
    Jan 18, 2009
    Messages:
    1,978
    Location:
    Nulkaba
    corsair have just released a white light kit for their ram:cool:
     
  11. OP
    OP
    Ace_finland

    Ace_finland Member

    Joined:
    Dec 11, 2012
    Messages:
    8
    Thats why i stopped working on the ram :)
     
  12. pheonix991

    pheonix991 Member

    Joined:
    May 16, 2005
    Messages:
    153
    Location:
    AR, USA
    Pretty neat!
     
  13. Toybox

    Toybox Member

    Joined:
    Jan 22, 2013
    Messages:
    19
    This is fantastic! What an awesome build. I love the sandwiched acrylic and your machine work is just spot on! I hope you sent some pics of to Coolermaster, I only wish I had the access to the tools you have! 100/10 from me!
     
  14. DaveRS

    DaveRS Member

    Joined:
    Dec 29, 2012
    Messages:
    151
    Location:
    Adelaide
    Amazing work, absolute masterclass right there. :thumbup:
     
  15. OP
    OP
    Ace_finland

    Ace_finland Member

    Joined:
    Dec 11, 2012
    Messages:
    8
    Thanks guys! New update coming in a few days :)
     
  16. WishBone17

    WishBone17 Member

    Joined:
    Nov 21, 2002
    Messages:
    4,349
    Location:
    Rouse Hill (Sydney)
    Holy CRAP this is ridiculous. Love it to death! awesome build
     
  17. koopz

    koopz Member

    Joined:
    Dec 27, 2001
    Messages:
    1,841
    Location:
    Qld
    I would seriously buy one of those for work

    *edit*

    and another for a mate for his computer shop. That'd look awesome (as well as being super handy) on the front bench
     

Share This Page